Administration and ownership

Switching Access Control Vendors Without Losing Control of Your Doors

← All articles

When you switch access control vendors, the building should keep control of four things: the administrator accounts for the system software and controllers, the user and credential records, the door schedules and access levels, and the physical documentation of devices and wiring. An access control system serves the building. Continuity should depend on what the owner holds, not on the outgoing vendor's goodwill.

What to pin down before any dates are set

Most of the risk in an access control vendor change sits in what nobody wrote down. Before scheduling anything, settle four unknowns.

Start with administrator access. The system software usually has accounts at different permission levels. The controller, the panel that decides whether to release a lock, often has its own programming login as well. List every account you can find and who uses it. If the only full administrator is a vendor technician, that is the first gap to close.

Next, find where the user and credential data lives. It can sit on a computer in the building, inside the controllers, or on a system the vendor hosts. The location decides how an export happens and who has to do it.

Then check what is recorded about each door: the reader, the lock, where the lock gets power, and which controller it wires back to. A door with no record is a door someone has to open up and trace during the switch.

Last, read your own agreement, proposal, and invoices for anything about records, software accounts, or system access. Do not assume either way. Where the wording is unclear, ask the outgoing vendor to confirm in writing what they will hand over.

Sequencing the handover so doors keep working

The order matters more than the speed. By the time the new vendor touches a door, the building should already hold what it would need if the old vendor stopped answering.

  1. Finish the audit and write down each gap.
  2. Request an export of user records, credential numbers, access levels, and schedules, plus screenshots or printouts of the configuration as a fallback.
  3. Get a building-controlled administrator login for the software and controllers, and confirm someone on staff can sign in with it.
  4. Have the incoming vendor inspect the existing readers, locks, wiring, and panels, then decide what stays in service.
  5. Schedule the cutover door by door or zone by zone, with a plan for how each door stays secured and usable between systems.
  6. Once every door is confirmed on the new system, disable the old vendor's accounts and remote access, and collect any cards or panel keys they hold.

Step four is a real decision. Cabling and panel enclosures often outlast the system they were installed for, and readers and locks can still be sound. What stays depends on what the incoming system can work with and on the condition of the hardware, so make that call after someone has looked at the doors, not from a parts list.

What goes in the handover package

Split the handover request in two. The first part is what the building keeps permanently, in its own files, no matter who services the system next.

  • Administrator usernames and passwords for the software and each controller
  • The current user list with names, credential numbers, and access levels, meaning the doors and times each group can use
  • Door schedules and holiday schedules
  • A door and device inventory: reader, lock type, door position switch (the sensor that reports whether the door is closed), exit device, and controller
  • Panel and power supply locations, cable routes, and where any intercom or buzzer system ties into door release
  • As-built drawings, wiring notes, and any software account details in the building's name

The second part is what the incoming vendor needs for the transition: copies of the export, the door inventory, and the drawings, plus temporary access to the old system if both will run side by side during cutover. The incoming vendor works from copies. The originals stay with you.

Risks to plan around during cutover

Credentials that stop working are what people notice first. A card that opened the door yesterday can fail at a new reader if the new system cannot read its format, or if card numbers were carried over wrong in the import. Checking the imported card numbers against the original export catches the second problem before anyone is standing at a locked door.

Doors caught between systems are the second risk. Electric locks come in two kinds. A fail-safe lock releases when it loses power, and a fail-secure lock stays locked. If a fail-safe door loses power partway through the switch, it is left unlocked. If a fail-secure door is cut off from its reader, cardholders can be stuck outside. Knowing which type each door has tells you whether that door needs someone posted at it or a key holder nearby.

The third is orphaned records. Old databases tend to hold former staff, lost cards, and tenants who moved out. Importing everything carries those gaps forward, so review the list with whoever manages tenants or staff before the import.

If you are planning a vendor change and want to talk through what the incoming scope should include, call Atlas Integrated Security at (347) 357-0985. Emergency service is available 24/7 if a door fails during the changeover.

Frequently asked questions

Should the outgoing vendor's administrator account be disabled before or after the new system is live?

The outgoing vendor's administrator account is usually disabled after the new access control system is live and each door has been checked, so the old records can still be consulted during cutover. Before cutover, the building should already hold its own full administrator login, so the vendor's account is never the only one that works.

Can existing credentials like cards or fobs be reused with a new vendor's system?

Existing cards and fobs can be reused only if the new readers and software can read their technology and number format. That depends on the specific cards and the incoming hardware. The practical way to find out is to test real cards from the building at a new reader before deciding whether to re-issue.

What if the old vendor will not provide the user records or configuration?

If an outgoing access control vendor will not hand over user records or configuration, put the request in writing and check what your agreement says about records. Meanwhile, rebuild from your own sources, such as tenant rosters and staff lists. Schedules can be redefined from how the building operates, and credentials re-enrolled on the new system.

Who should keep a copy of door and wiring documentation after the switch?

Door and wiring documentation for an access control system should live with the building, in files the owner or facility team controls, with a copy given to whichever vendor services the system. Keeping the original in-house means the next repair or vendor change starts from a known record instead of tracing cables.

Next step