Door access control can often work with existing locks and doors, but the answer comes one door at a time. The door and frame often stay. What decides the rest is the frame material, the condition of the existing latch, how well the door closes and lines up, and how the opening has to release so people can always get out.
Can access control be added without replacing the door?
Access control adds a lock that releases on a signal from a card reader. That electrified part attaches to an opening made of several pieces. The door leaf is the slab that swings. The frame surrounds it. The latch or lock sits in the door, and the strike plate sits in the frame where the latch catches.
The leaf and frame often stay. The strike usually changes, the lockset sometimes does, and a low-voltage cable needs a route to the door. A solid door in a sound frame is a good start. A door that drags, sags, or has been patched around the lock needs attention first, because new hardware depends on the door closing the same way each time. Judge each opening on its own.
Option A: an electric strike uses the latch already there
An electric strike replaces the plain strike plate in the frame and works with the latch already in the door. When the reader grants access, a hinged piece in the strike called the keeper releases, so the latch can push past it without anyone turning the handle.
Fit depends on the frame first, which needs room behind the plate for the strike body. Latch type matters too, since lever locksets, mortise locks, and panic bars each pair with different strikes. Then alignment. If you have to push or lift the door to make it latch today, a strike will bind the same way. The inside handle is untouched, so people leave as they always have.
Option B: a magnetic lock holds the door at the frame
A magnetic lock, or mag lock, is an electromagnet mounted on the frame header, with a steel plate called the armature fixed to the door. While powered, the magnet holds the plate. Cut the power and the door is free. The existing latch plays no part.
Mag locks suit doors where a strike has nowhere to go, such as some glass storefront doors. A mag lock needs the armature to meet the magnet flat, a solid header to mount on, and a closer that brings the door fully shut. A door that sits out of square holds poorly.
Exit is the bigger dependency. A mag lock does not release when someone turns a handle, so something has to cut its power, such as a motion sensor, a push button, or a link to the fire alarm. The old latch also needs a decision, because a latch that still locks would work against a door meant to release electrically.
When is an electric strike better than a magnetic lock?
An electric strike usually makes more sense when the existing latch works well, the frame has room, and the door should stay locked from outside during a power loss. A strike can be set fail-secure, meaning locked without power, or fail-safe, meaning unlocked without power. Either way, the inside handle still lets people out.
A magnetic lock makes more sense when the door has no usable latch, the frame cannot take a strike, or the opening should release on power loss. Exit then depends on the release devices, and the door is unsecured in an outage unless backup power holds it. Heavy traffic wears both kinds, so a sagging or slamming door is usually repaired before either is chosen.
How are fire exits handled during an access control upgrade?
At an exit door, the deciding question is how everyone gets out, including during a power failure or a fire alarm. Stairwell doors, panic bar doors, and fire-rated doors and frames are reviewed apart from ordinary entry doors. A strike on a panic bar door leaves the bar's mechanical exit in place. A mag lock puts exit in the hands of its release devices. Cutting or adding hardware on a fire-rated opening can affect its rating. Confirm the requirements for each exit with the local building or fire authority before hardware is chosen.
What to note about each door before an assessment
A few notes per door make an assessment far more useful. Walk each opening and write down:
- Door material and type: hollow metal, wood, or aluminum and glass, single or pair.
- Frame material, and whether the door closes and latches on its own.
- The current lock: lever, mortise, panic bar, or deadbolt only.
- Whether the door is an exit, a stairwell door, or labeled fire-rated.
- Any existing door operator or push plate.
- Nearby cabling, ceiling access, or a reader already on the wall.
Atlas Integrated Security handles access control along with the commercial door hardware, commercial smart locks, and low-voltage cabling behind it, plus ADA door operators where an opening has or needs one, for buildings across New York City's five boroughs, Long Island, and Jersey City. To talk through your door notes, call Atlas Integrated Security at (347) 357-0985.
Frequently asked questions
Does a door with an existing ADA door operator need different planning for access control?
A door with an ADA door operator does need different planning. The operator swings the door by motor, so the lock has to release before the operator starts to open it. If the timing is off, the operator pushes against a door that is still locked. The reader, the lock, and the operator's activation are planned to work in sequence.
What happens to an electrified door when power is lost?
An electrified door behaves according to its hardware. A magnetic lock releases when power is removed. An electric strike set fail-safe unlocks, while one set fail-secure stays locked from outside and still lets people out with the inside handle. Backup power can keep the hardware running through an outage.
Can a keyed door stay usable by key after access control is added?
A keyed door often stays usable by key when an electric strike is added, because the existing lockset and cylinder remain in the door. With a magnetic lock, the key does not control whether the door holds, since the magnet ignores the latch. Some setups add a key switch to release the magnet.
Who should confirm egress requirements for a specific opening?
Egress requirements for a specific opening should be confirmed with the local building or fire authority, often through the building's architect or design professional. Requirements can differ by door, especially at stairwells, panic bar doors, and fire-rated openings, so confirming them early avoids choosing hardware that has to change later.
Tell us about the building.